Dell Latitude D530 Intel GMA X3100 - ML with full QE/CI

[DaFOB]

I take no credit for this guide.  Hervé and the folks at MacRumors did all the heavy lifting.  All I did was do some testing and tweaking to get all their hard work and research working on the Dell Latitude D530.  What follows is a result of everyone's efforts...

 

 

 

This guide applies to the D530 1400x1050 models. This guide was made with purchased copy of ML 10.8.0. It was not tested with purchased copies of ML 10.8.1, 10.8.2 or 10.8.3. Contributions/confirmations/issues are welcome on that matter.

 

The attached bootpack was made out of the D630 nVidia ML bootpack and the DSDT file was just replaced with a modified DSDT file taken from the D630 X3100 HiRes boot pack.

 

Extra_D530_ML.zip

 

This guide assumes you're using a blank HDD, partitioned and formated GUID or MBR partitioned HDD.  Also, have an external USB mouse or keyboard available.  At some point during these steps, the built-in trackpad or keyboard may not work and you might need to plug in external devices to proceed to the next step. 

 

 Read the MacRumors guide thoroughly and follow it to the letter as far as creating the installer is concerned. Basically, if you don't have a legit copy of ML with the "Install Mountain Lion.app" application, forget it. The tool requires you to copy it to your "Applications" folder. It won't work if all you have is the InstallESD.dmg image.

http://forums.macrumors.com/showthread.php?t=1325709

 

 Do not ask questions about MLPostFactor here. Go to the authors at MacRumors. It's not our hack, we did not make it, we don't support it.

 

 

Phase 1: initial ML installation in mainstream 64bit kernel mode with unsupported graphics

1. make the usual myHack USB installer (ML 10.8.0), using the attached bootpack.
   
2. boot myHack installer and install ML 10.8.0, pointing to the /Extra folder of the installer media when prompted for the boot pack (do not choose generic).
   
3. reboot into ML and complete 1st boot setup.
   
4. you're now in ML 10.8.0 with default graphics at 1024x768 and without graphics acceleration.
   
5. If you have not already done so, remove your myHack USB installer and put it aside.
   
6. install combo update 10.8.3 (your wireless may not be supported at that stage, so use Ethernet port or install appropriate Wifi kext).
   
7. the combo update might fail. This is normal. Before rebooting, run myHack and choose myFix -> Quick
   
8. reboot into ML 10.8.3, still with default graphics and without acceleration.
   
9. if you have used myHack 3.2 to install ML, you may encounter KP on EFIRunTime/EFINVRAM at reboot. Boot ML off your USB installer, download & run Chameleon Wizard and install Chameleon v2248 or later on your ML partition. If you have used myHack 3.1.2, you should be Ok.
   

Phase 2: MLPostFactor

1. download MLPostFactor off the Net (EDIT 28 Mar 2015: sorry, original links posted in 2013 are dead now)
   
2. create a new small partition on your HDD (8 to 16GB) or insert and erase your myHack USB installer (or any other available external media).
   
3. following MLPF instructions to the letter, run MLPostFactor and create an ML installer on the freshly created spare HDD partition or freshly erased USB key. Select the "ML 10.8.0->10.8.2" case and run the app. If you've purchased and downloaded ML 10.8.3, select that version instead.
   
4. upon completion, create a folder called "Extra" at the root of that installer media and copy DSDT table + SMBIOS & Cham boot plist files there.
   
5. be prepared with a USB mouse and keyboard ready.  The MLPostFactor that you just created may not have the appropriate kexts for the D530 trackpad or built-in keyboard.
   
6. reboot off your initial ML disk/partition, interrupt the boot process at the Chameleon delay bar and select this newly created ML installer partition/disk with options & flag: DSDT=/Extra/<dsdt filename> arch=i386 -f
   
7. once installer is loaded, do not actually proceed with any installation (it would not be bootable). Go to "Utilities" in the menu bar and select MLPostFactor.
   
8. when MLPostFactor app kicks in, click "Continue" until you're offered to select a destination volume.
   
9. in the list available under the HDD icon, select your previously-made ML 10.8.3 installation, check the "10.8.3" case and click "Install MLPostFactor".
   
10. upon completion, click "Quit MLPostFactor", quit installation program and reboot ML 10.8.3 with flag and boot option: "-f arch=i386".  You will now have full QE/CI !
    
11. you may notice that not all of your devices such as trackpad, battery meter, wireless, etc. may be present or working.
    
12. launch myHack and run myFix. Choose the quick version.
    
13. open up Chameleon wizard and go to the boot plist. Check "Ignore Boot Cache (-f)" case and "32-bit (i386)" case. They're required from now on.
    
14. Reboot and everything should be working, including full QE/CI!  Sleep should also work, but if not launch terminal and type "sudo pmset hibernate mode 0"
    

 

That's it, enjoy ML on your previously unsupported D530 X3100.

 

Remember that this hack is quite aggressive in the way it reverts to DP1 files and older graphics drivers (GMA950 kexts, OpenGL libraries), so you may find that things do not work. Again, don't ask for support here, go to the authors at MacRumors.

 

[Hervé]

Great news, thanks DaFOB. Another one to the list...

[Hervé]

To update to 10.8.4, use Combo Update + MLPF v0.3 as explained in D430 guide here: https://osxlatitude.com/index.php?/topic/2467-installing-ml-on-d430-gma950-with-full-qeci/&do=findComment&comment=20838

 

To install 10.8.4 directly, apply the installation procedure with 10.8.4 install app & MLPF v0.3 from the onset.

[Hervé]

Updated Phase #1 of the procedure to take into account KP issue that happens with myHack3.2 installations booting in 32bit kernel mode:

-> need Chameleon v2248 or above on ML partition to fix the issue.

[Hervé]

For ML 10.8.5, whether an update from an earlier release or a direct installation, follow exact same process as for ML 10.8.4 with MLPF v0.3 for ML10.8.4 (MLPF having never updated to reflect for ML 10.8.5).

[Hervé]

 Warning   

 
Apple freshly published Security Update 2014-004 1.0 breaks MLPF installation. It reinstates IOHIDFamily.kext v1.8.1 in /S/L/E which subsequently breaks startup. The fix is to revert to the previous MLPF version v1.7.1 of the kext. To do this easily, just install the attached kext in /E/E and run myFix (quick). The system will then be restored to full operation.
 
The kext is available here.

[Hervé]

Warning
 
Apple's Security Update 2015-001 breaks MLPF installations. It installs:
i) a new kernel v12.6.0
ii) a new System.kext v12.6.0
 
The security update can only be safely be applied on a MLPF installation if the following actions are undertaken before subsequent reboot:
1) replace new ML kernel v12.6.0 by DP1's v12.0.0
2) replace new System.kext v12.6.0 by DP1's v12.0.0 directly in /S/L/E (do not place it /E/E, it won't work)
 
Unless those replacements are done, the MLPF installation will be unbootable.
 

The following 3 kexts also appear to need roll-back in order to retain Bluetooth services and kextcache:

1) IOBluetoothFamily.kext (back to v4.0.8)

2) IOBluetoothHIDDriver.kext (back to v4.0.8)

3) IOSerialFamily.kext (back to v10.0.5)

 

Whilst you're encouraged to keep a backup, the files are available here.

[Hervé]

I've noticed that AppStore may keep offering to install that security update after initial installation. But after 2 or 3 re-installations, the security update stopped popping up...

[Hervé]

Apple's Security Update 2015-004 will again break MPLF. In addition to the same files as mentioned above, it also installs IOSurface kext v86.0.5 in /S/L/E. A rollback to version v80.0.2 is necessary to fix the MLPF installation.

 

The file is available here.